{"product_id":"high-power-mosfet-pwm-switch-module-4-60v-10a","title":"High-Power MOSFET PWM Switch Module DC 4–60V 10A 600W (Dual MOS, Optocoupler Isolated)","description":"\u003cp\u003e\u003cstrong\u003eThe high-power MOSFET PWM switch module is an isolated electronic switch board that lets a low-voltage signal from an Arduino, ESP32, Raspberry Pi, PLC or a plain switch turn on, turn off or PWM-dim a DC load of up to 10 A and 600 W, replacing a mechanical relay for motors, LED lighting, pumps, fans and heaters.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIsolated high-power switching module for driving DC motors, LED strips, lamps, pumps, solenoids and heaters from a microcontroller, PLC or a simple switch. Dual parallel MOSFETs deliver 10 A continuous (600 W) across a wide 4–60 V input range, and a PWM input (0–2.5 kHz) lets you control motor speed or lamp brightness directly. Optocoupler isolation protects your controller. Note: use only one trigger type at a time; keep high-level signals between 3.0–24 V and low-level signals below 0.6 V.\u003c\/p\u003e\u003ch2\u003eWhat can you use it for?\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpeed control of DC motors, fans and water pumps with a PWM signal\u003c\/li\u003e\n\u003cli\u003eDimming 12 V \/ 24 V LED strips and lamps\u003c\/li\u003e\n\u003cli\u003eSwitching heaters, solenoid valves, electromagnets and 3D-printer heated beds\u003c\/li\u003e\n\u003cli\u003eSilent, spark-free replacement for relays in automation and vehicle projects\u003c\/li\u003e\n\u003cli\u003eHigh-current output stage for Arduino, ESP8266\/ESP32, Raspberry Pi and PLC controllers\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWho is it for?\u003c\/h2\u003e\u003cp\u003eElectronics hobbyists, automation engineers, students and repair shops that need a ready-made high-current switch without designing a MOSFET driver circuit.\u003c\/p\u003e\u003ch2\u003eCompatibility\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSignal sources: 3.3 V \/ 5 V microcontroller pins (Arduino, ESP32, Raspberry Pi, STM32), PLC outputs, 12–24 V control lines, mechanical switches\u003c\/li\u003e\n\u003cli\u003eLoads: any DC load from 4 V to 60 V up to 10 A continuous (15 A with extra cooling), 600 W maximum\u003c\/li\u003e\n\u003cli\u003ePWM: 0–2.5 kHz signal frequency for motor speed or LED brightness control\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eSpecifications\u003c\/h2\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eOperating voltage\u003c\/th\u003e\n\u003ctd\u003eDC 4–60 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eContinuous current\u003c\/th\u003e\n\u003ctd\u003e10 A at room temperature (up to 15 A with extra cooling)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMax power\u003c\/th\u003e\n\u003ctd\u003e600 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTrigger modes\u003c\/th\u003e\n\u003ctd\u003eHigh-level (DC 3.0–24 V), low-level (DC 0–0.6 V), dry-contact switch, PWM\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePWM frequency\u003c\/th\u003e\n\u003ctd\u003e0–2.5 kHz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eIsolation\u003c\/th\u003e\n\u003ctd\u003eOptocoupler-isolated signal input\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutput stage\u003c\/th\u003e\n\u003ctd\u003eDual parallel MOSFETs, active output, low RDS(on)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e−40 to 85 °C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBoard size\u003c\/th\u003e\n\u003ctd\u003e46.5 × 29 × 12 mm, 2 mm mounting holes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eIndicator\u003c\/th\u003e\n\u003ctd\u003eON LED shows output state\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch2\u003eWhat's in the box\u003c\/h2\u003e\u003cul\u003e\u003cli\u003e\n\u003cstrong\u003eDefault Title:\u003c\/strong\u003e 1 × MOSFET PWM switch module with screw terminals\u003c\/li\u003e\u003c\/ul\u003e\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\u003ch3\u003eCan I control this module with an Arduino or ESP32?\u003c\/h3\u003e\u003cp\u003eYes. Connect a 3.3 V or 5 V output pin to the high-level trigger input and GND to signal ground. A PWM pin lets you vary speed or brightness.\u003c\/p\u003e\u003ch3\u003eWhat is the maximum load?\u003c\/h3\u003e\u003cp\u003e10 A continuous at room temperature and 600 W total, on any supply voltage between DC 4 V and 60 V. With a heatsink or fan the module handles up to 15 A.\u003c\/p\u003e\u003ch3\u003eDoes it work with 12 V and 24 V loads?\u003c\/h3\u003e\u003cp\u003eYes. 12 V and 24 V motors, LED strips, pumps and fans are the most common use; anything from 4 V to 60 V DC is supported.\u003c\/p\u003e\u003ch3\u003eIs the input isolated from the load?\u003c\/h3\u003e\u003cp\u003eYes. An optocoupler separates the control signal from the power side, protecting your microcontroller from the high-current circuit.\u003c\/p\u003e\u003ch3\u003eCan I use AC loads?\u003c\/h3\u003e\u003cp\u003eNo. This is a DC-only MOSFET switch. For AC lamps or appliances use a solid-state relay instead.\u003c\/p\u003e\u003ch3\u003eWhat is the difference between high-level and low-level trigger?\u003c\/h3\u003e\u003cp\u003eHigh-level trigger switches on with 3.0–24 V on the input; low-level trigger switches on when the input is pulled to 0–0.6 V. Use only one trigger method at a time and avoid signal voltages between 0.6 V and 3.0 V.\u003c\/p\u003e","brand":"Glunova Biotech","offers":[{"title":"Default Title","offer_id":50739663601903,"sku":"MOS-PWM-60V10A","price":9.0,"currency_code":"SGD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0821\/5406\/2063\/files\/04c.jpg?v=1789176532","url":"https:\/\/armdojo.com\/products\/high-power-mosfet-pwm-switch-module-4-60v-10a","provider":"ArmDojo","version":"1.0","type":"link"}